null

NEW INVENTORY COMING IN DAILY! FREE SHIPPING OVER $199.*some exclusions

Bell

BELL Helmet, K1 Matte Black Large, Snell SA2025 Head and Neck Support Ready

(No reviews yet) Write a Review
SKU:
BEL1420D05
Weight:
3.00 LBS
Shipping:
Calculated at Checkout
  • BELL Helmet, K1 Matte Black Large, Snell SA2025 Head and Neck Support Ready
  • BELL Helmet, K1 Matte Black Large, Snell SA2025 Head and Neck Support Ready
  • BELL Helmet, K1 Matte Black Large, Snell SA2025 Head and Neck Support Ready
  • BELL Helmet, K1 Matte Black Large, Snell SA2025 Head and Neck Support Ready
$599.95

Description

Bell K1 Matte Black Large SA2025 Helmet

K1 Sport (SA2025)

 
Sport Series
 

The K1 Sport is a race-ready, multi-use, and versatile helmet with superior ventilation combined with modern styling built for the entry-level racer who demands quality at an affordable price. Incorporating a lightweight composite shell, excellent fit, and multiple ventilation options, the all-purpose K1 Sport is a perfect choice for entry level or hobbyist racers.

    • Lightweight composite shell
    • Advanced multi-density, multi-piece liner to maximize energy absorption and impact performance
    • Superior ventilation with direct flow chin bar vents, forehead vents, and top vents
    • Air Intake, rear spoiler, top gurney, and chin bar gurneys available separately
    • Forced air attachments available separately for use with external cooling systems
    • M6 terminals for FHR anchor attachment and homologated for use with approved head and neck devices
    • Synthetic rubber gasket seal to prevent dirt and water from entering the helmet
    • Shield and pivot kit: 287 SRV, SRV-1
    • Incorporating the same powerful and effective top air intake vents and pattern as the RS7, allowing air intake vent kits and top forced air kits developed for the RS7 models to be fully compatible

HELMET
CARE AND MAINTENANCE

 

Proper care and maintenance are important in keeping your helmet in race-ready condition. The following exterior and interior care recommendations will help assure your helmet functions properly and is in peak condition.

 

Exterior care

 

All Bell Helmets are finished with a tough, polyurethane coating which resists scratching. When cleaning the exterior of your helmet, only use the highest quality products that are used for automotive finishes. It is up to the consumer to take great care of their helmet to assure no accidental damage is done to the helmet that may compromise the safety factor of the helmet. Do not use any abrasive or solvent based cleaners on the exterior of your helmet.

 

Interior care

 

The interior of the helmet is often susceptible to dirt and excess moisture. When cleaning the interior of your helmet, only use mild soap and water with a rag to hand wash the interior fit pad. When the interior of the helmet has become wet, allow the helmet to dry before putting it away for storage. We recommend properly drying and cleaning your helmet after every use to assure the best comfort level possible.

SIZING

CERTIFICATIONS

  • Snell SA2025

The circumference of the head should be measured at a point approximately one inch above the eyebrows in front, and at a point in the back of the head that results in the largest possible measurement. Take several measurements. The largest measurement is the one you want to try on first. If you use a balaclava or head sock, always measure and fit the helmet with it on. Use the Bell sizing chart to determine the size that best matches the head measurement. 

Size Comparison Chart

Standard SizeHat SizeInchesCentimeters
4XS 6 3/8 20 1/16 51
3XS 6 1/2 - 6 5/8 20 1/2 - 20 7/8 52-53
2XS 6 3/4 - 6 7/8 21 1/2 - 21 5/8 54-55
XS 7 22 56
S 7 1/8 22 3/8 57
M 7 1/4 - 7 3/8 22 3/4 - 23 1/4 58-59
L 7 1/2 23 5/8 60
XL 7 5/8 - 7 3/4 24 - 24 3/8 61-62
2XL 7 7/8 - 8 24 3/4 - 25 1/4 63-64
3XL 8 1/8 - 8 1/4 25 5/8 - 26 65-66
4XL 8 3/8 - 8 1/2 26 3/8 - 26 3/4 67-68

 

Proper Helmet Fit

When properly fitted, the helmet should be worn low on the brow, the eyes near the center of the eye opening, touching the top of the head with uniform and firm pressure all around - tight without excessive pressure points. Consult the How To Fit A Helmet page on the Bell Racing website for more information.   

Proper helmet fit is vital to the performance of a helmet during an impact. For the helmet to perform properly during an impact, it must stay securely on the head.

Measuring the head is only a starting point for the entire sizing procedure. Due to varying shapes, heads that are apparently the same size when measured by a tape may not necessarily fit the same size helmet.

A small metal tape measure or a cloth tape may be used to make your initial measurement. You can also use a string, which can then be laid against a measuring tape.

Measure the circumference of the head at a point approximately one inch above the eyebrows in front, and at a point in the back of the head that results in the largest possible measurement. Take several measurements. The largest measurement is the one you want to use.

Size Comparison Chart

Standard SizeHat SizeInchesCentimeters
       
S 7 1/8 22 3/8 57
M 7 1/4 - 7 3/8 22 3/4 - 23 1/4 58-59
L 7 1/2 23 5/8 60
XL 7 5/8 - 7 3/4 24 - 24 3/8 61-62
       

PLEASE NOTE: 

NOT ALL SA2025 HELMETS ARE AVAILABLE YET SO WE ARE JUST LISTING COLOR AND SIZES OF HELMETS WE ACTUALLY HAVE,

BUT WE MAY BE ABLE TO GET MORE SIZES, SO PLEASE CHECK WITH US IF YOU ARE LOOKING FOR SOMETHING DIFFERENT OTHER THAN THE CHOICES SHOWN ABOVE.

 

 

View AllClose