Bell
BELL Helmet, M-8 White Large, Snell SA2020 Head and Neck Support Ready
- SKU:
- BEL1419A05
- Weight:
- 3.00 LBS
- Shipping:
- Calculated at Checkout
Description
Bell M.8 White Large SA2020 Helmet
FEATURES
- Lightweight composite shell
- Advanced multi-density, multi-piece liner to maximize energy absorption and impact performance
- Versatile ventilation system direct flow front chin bar ventilation and upper manual lever air intake vents that can be opened and closed
- Integrated channels in face piece offer multiple options to install drink tube and radio systems
- M6 terminals for FHR anchor attachment and homologated for use with approved head and neck devices
- Largest size range available in the Bell Racing product line
- Large eyeport for enhanced vision
- Synthetic rubber gasket seal to prevent dirt and water from entering the helmet
- Shield and pivot kit: SRV-8, SRV-1
- Homologation: Snell SA2020
- Colors: White and Matte Black
- Sizes: XXS, XS, S, M, L, XL, 2XL, 3XL, 4XL
IN THE BOX
- M8
- Clear SRV-8 Shield Installed
- Manual Lever Air Intake Vents Installed
- Draw String Helmet Bag
- Plastic Tearoff Post Kit
- 3 Stainless Circle Grommets
- Hex Wrench Key
SIZING
- XXS, XS, S, M, L, XL, 2XL, 3XL, 4XL
- Sizing Chart
- Helmet Fitting Guide
CERTIFICATIONS
- Snell SA2020
The circumference of the head should be measured at a point approximately one inch above the eyebrows in front, and at a point in the back of the head that results in the largest possible measurement. Take several measurements. The largest measurement is the one you want to try on first. If you use a balaclava or head sock, always measure and fit the helmet with it on. Use the Bell sizing chart to determine the size that best matches the head measurement.
Size Comparison Chart
Standard Size | Hat Size | Inches | Centimeters |
---|---|---|---|
4XS | 6 3/8 | 20 1/16 | 51 |
3XS | 6 1/2 - 6 5/8 | 20 1/2 - 20 7/8 | 52-53 |
2XS | 6 3/4 - 6 7/8 | 21 1/2 - 21 5/8 | 54-55 |
XS | 7 | 22 | 56 |
S | 7 1/8 | 22 3/8 | 57 |
M | 7 1/4 - 7 3/8 | 22 3/4 - 23 1/4 | 58-59 |
L | 7 1/2 | 23 5/8 | 60 |
XL | 7 5/8 - 7 3/4 | 24 - 24 3/8 | 61-62 |
2XL | 7 7/8 - 8 | 24 3/4 - 25 1/4 | 63-64 |
3XL | 8 1/8 - 8 1/4 | 25 5/8 - 26 | 65-66 |
4XL | 8 3/8 - 8 1/2 | 26 3/8 - 26 3/4 | 67-68 |
Proper Helmet Fit
When properly fitted, the helmet should be worn low on the brow, the eyes near the center of the eye opening, touching the top of the head with uniform and firm pressure all around - tight without excessive pressure points. Consult the How To Fit A Helmet page on the Bell Racing website for more information.
Proper helmet fit is vital to the performance of a helmet during an impact. For the helmet to perform properly during an impact, it must stay securely on the head.
Measuring the head is only a starting point for the entire sizing procedure. Due to varying shapes, heads that are apparently the same size when measured by a tape may not necessarily fit the same size helmet.
A small metal tape measure or a cloth tape may be used to make your initial measurement. You can also use a string, which can then be laid against a measuring tape.
Measure the circumference of the head at a point approximately one inch above the eyebrows in front, and at a point in the back of the head that results in the largest possible measurement. Take several measurements. The largest measurement is the one you want to use.
Size Comparison Chart
Standard Size | Hat Size | Inches | Centimeters |
---|---|---|---|
S | 7 1/8 | 22 3/8 | 57 |
M | 7 1/4 - 7 3/8 | 22 3/4 - 23 1/4 | 58-59 |
L | 7 1/2 | 23 5/8 | 60 |
XL | 7 5/8 - 7 3/4 | 24 - 24 3/8 | 61-62 |